This post may contain affiliate links. Read the full disclosure here
This tutorial is all about how I made a mini quilted keychain using a quilt-as-you-go method.
I am using this blog to motivate me to refresh and improve my sewing skills. One thing I always wanted to do but haven’t done much of is quilting. So I decided to start with a really small beginner’s project to build my confidence.
I have been reading and watching tutorials on a whole range of quilt-as-you-go techniques lately as I think that is probably the most realistic way for me to get started with quilting.
The method that appealed to me most was the one where you quilt fabric strips straight on to the batting and backing. The backing fabric is cut larger than the batting so that when you are done several squares you can sew them together and fold the excess over to form the binding.
Since I am a bit allergic to creating bias binding from scratch (not to mention fiddling with pinning it on!) I thought this sounded like a method I could get on board with!
So I decided to start with one mini-block as a little beginner project and turn it into a keychain.
Here is how I did it.
- Backing fabric square – mine was 4″ x 4″ (10cm x 10cm)
- Batting fabric square – I did two versions – one with a 2 & 1/4″ square and one with a 2 & 3/4″ square.
- Fabric scraps
- Scrap of ribbon
- Two buttons
Step 1: Choose your backing fabric
So I already had the backing fabric cut into a square from when I had cut up a bunch of scraps about two years ago thinking I was going to start quilting and never did….my stash of scraps and half finished projects is ridiculous!
The backing square was 4″ by 4″ so I took that as my starting point.
Step 2: Cut your batting square
If you have cotton batting to hand you can absolutely use it for this.
But as I was using this as a bit of a practice project I decided to cut up an old towel instead. I used a 100% cotton towel as with this quilt-as-you-go method you iron straight onto the batting.
I ended up doing two versions of this, for the first my batting square was slightly smaller – about 2 &1/4″ square and for my second I cut my batting square a bit bigger to 2 & 3/4″ square. Both with the same size backing square (see the photos above and below for how that effected the size of the quilted block).
The important thing is that there is enough backing fabric to fold over twice and cover the edge of your batting square. You can decide how thin or thick you want the binding to be – so use what you have and don’t stress about the exact size of this.
Step 3: Pick your Scraps!
I found some fabric scraps I liked the look of and even a couple crumbs that had puncture marks in them from a previous sewing project!
The main thing I was looking for was for each strip to stretch across the batting square diagonally.
Where they didn’t quite fit I sewed two scraps together to lengthen them.
Step 4: Get quilting!
I placed my first two strips right sides together diagonally on my batting square and sewed through the strips, the batting and the backing all at once.
I then repeated this on the other edge of the centre strip and pressed with an iron to get them laying flat.
I repeated this on the outside rows with smaller crumbs. It didn’t take long until my batting fabric was completely covered.
Step 5: Cut off excess
When I was done sewing on my strips I flipped the block over and pinned back the excess backing fabric.
I then trimmed away the excess edges of the scrappy strips to clean up the edges around the batting.
Step 6: Binding
Once the edges were all cleaned up I folded each side of the backing fabric over twice (to hide the raw edges) and placed over the edge of the batting square.
You then stitch it in place and that’s your binding!
I did some trimming when I got to the corners to help them sit a little neater, but I’m not a hospital corners expert so happy to take any tips you have on getting the corners a little crisper!
Step 7: Key Chain Loop
Before I finished my last edge of binding I tucked in the raw edges of a folded loop of ribbon – above one binding edge and below the next.
I then sewed that in place to form the keychain loop.
Step 8: Buttons (to cover the flaws!)
I wasn’t super happy with how the ribbon jutted out so I folded it behind at the back and secured it in place with buttons to the front and back.
Step 9: Add a keyring
Obviously lastly you need to add the actual keyring for your keys to go on. I buy these in big packs so I can make little projects like these whenever the mood strikes me – keychains are good gifts too!
Finished Mini Quilt-as-you-go Keychain!
I think it’s pretty cute and it was a great way to put some of the skills into practice I’d been reading about without committing to a big project!
There were two things I wasn’t super happy about with my first go (the blue one) that I wanted to do differently after I was done. The greenish one was my second attempt.
The first was I didn’t love how the stitching looked at the back – this could have been improved with a different thread colour choice but for my second go I decided to try just quilting on the batting and adding the backing square to bind after.
That turned out much neater but I think it would be more difficult to do if you were adding additional blocks to form a quilt or working with bigger blocks, then you would really need to quilt through.
What is your qulit-as-you-go method? Any tips you swear by that you want to share – please drop them in the comments!
The second thing I didn’t love was how the keychain loop ribbon sat.
So for my second go around instead of sewing it into the binding I placed it to the back and hand stitched it down. I still added the buttons to finish it off but I think it sits a little neater this way.
Any tips for adding hanging loops in corners like this? I’d love to hear them!
If you like this idea and you want to save it for later don’t forget to pin it to your quilting or scrap fabric projects board!
Looking for some more scrapbusting ideas? Try these posts: